Modelling and Optimization of Strut Configurations in Aircraft Landing Gear Assembly for Effective In-Service Duty Cycle

Ikechukwu Owunna; Michael  Bassey; Imoh Ekanem; Aniekan Ikpe

doi:10.66972/iscis21202610

Authors

Ikechukwu Owunna Department of Mechanical Engineering, University of Benin, Edo State, Nigeria Author https://orcid.org/0000-0002-6641-0446
Michael Bassey Department of Mechatronics Engineering Technology, Akwa Ibom State Polytechnic Ikot Osurua, Ikot Ekpene, Akwa Ibom State Nigeria Author https://orcid.org/0000-0002-3592-0558
Imoh Ekanem Department of Mechatronics Engineering Technology, Akwa Ibom State Polytechnic Ikot Osurua, Ikot Ekpene, Akwa Ibom State Nigeria Author https://orcid.org/0000-0002-8973-9260
Aniekan Ikpe Department of Mechatronics Engineering Technology, Akwa Ibom State Polytechnic Ikot Osurua, Ikot Ekpene, Akwa Ibom State Nigeria Author https://orcid.org/0000-0001-9069-9676

DOI:

https://doi.org/10.66972/iscis21202610

Keywords:

Strut Configuration, FEA, Landing Gear, Optimization, Duty cycle

Abstract

The landing gear configuration system is one of the most critical systems, subjected to intense dynamic loads and failure during landing and taxiing operations. The optimization of this system is of key importance to the aviation industry, with clear and direct effects ranging from integrity, safety, and fuel efficiency to maintenance dynamics. The present study focuses on the modelling and optimization of strut configurations in an aircraft landing gear assembly for an effective in-service duty cycle. Two strut configurations, consisting of a conventional single strut and an optimized dual strut, were modelled and comparatively analyzed using parametric CAD tools as well as Finite Element Analysis (FEA) within the SolidWorks simulation environment. The modelling and simulation involve the load and stress analysis of critical components, ranging from the main strut, retraction mechanisms, torque links, torque bars, and wheels to the actuator and main support. This approach was geared towards the premise of analyzing and optimizing the landing gear system by achieving weight reduction without compromising structural integrity. This was achieved through FEA of the design model. The simulation results showed that achieving a conservative 5% reduction in weight would translate into a decrease of approximately 1,045 kg in the aircraft's operating empty mass, which further translates into a reduction in the aircraft's energy consumption during its in-service duty cycle. The results further revealed that the developed model can effectively support the prediction and analysis of the mechanical behaviour of the landing strut.

Downloads

Download data is not yet available.

References

Singh, J., Srivastawa, K., Jana, S., & Dixit, C. (2024). Advancements in lightweight materials for aerospace structures: A comprehensive review. Acceleron Aerospace Journal, 2(3), 173–183. https://doi.org/10.61359/11.2106-2409

Simões, S. (2024). High-performance advanced composites in multifunctional material design: State of the art, challenges, and future directions. Materials, 17(23), 5997. https://doi.org/10.3390/ma17235997

Tunca, E., Kafali, H., Keskin, G., & Kuşhan, M. C. (2022). Landing gear systems in aircraft. In Materials, Structures and Manufacturing for Aircraft (pp. 153–179). Springer International Publishing. https://doi.org/10.1007/978-3-030-91873-6_7

Liseitsev, N. K. (2025). Landing gear design. In Aircraft Design (pp. 737–768). Springer Nature Singapore. https://doi.org/10.1007/978-981-96-4599-2_21

Khan, S. A., Mehmood, Z., & Afshan, Z. (2021). Design, analysis and topology optimization of a landing gear strut for a quadcopter upon impact. In 2021 International Conference on Applied and Engineering Mathematics (ICAEM) (pp. 37–42). IEEE. https://doi.org/10.1109/ICAEM53552.2021.9547116

Liu, Y., Pan, L., Cui, Q., & Meng, D. (2023). A case study on structural optimization design of shock absorber brackets in automobile suspension. IEEE Access, 11, 131064–131072. https://doi.org/10.1109/ACCESS.2023.3334146

Shanmugasundar, G., Dharanidharan, M., Vishwa, D., & Kumar, A. S. (2021). Design, analysis and topology optimization of connecting rod. Materials Today: Proceedings, 46, 3430–3438. https://doi.org/10.1016/j.matpr.2020.11.778

Delprete, C., Dagna, A., & Brusa, E. (2023). Model-based design of aircraft landing gear system. Applied Sciences, 13(20), 11465. https://doi.org/10.3390/app132011465

Deng, K., Ompusunggu, A. P., Xu, Y., Skote, M., & Zhao, Y. (2025). A review of material-related mechanical failures and load monitoring-based structural health monitoring (SHM) technologies in aircraft landing gear. Aerospace, 12(3), 266. https://doi.org/10.3390/aerospace12030266

Raouf, I., Kumar, P., Cheon, Y., Tanveer, M., Jo, S. H., & Kim, H. S. (2025). Advances in prognostics and health management for aircraft landing gear—Progress, challenges, and future possibilities. International Journal of Precision Engineering and Manufacturing-Green Technology, 12(1), 301–320. https://doi.org/10.1007/s40684-024-00646-4

Filippatos, A., Markatos, D., Theochari, A., & Pantelakis, S. (2025). Integrating sustainability in aircraft component design: Towards a transition from eco-driven to sustainability-driven design. Aerospace, 12(2), 140. https://doi.org/10.3390/aerospace12020140

Piçak, S. C., Yahşi, M., & Gültekin, E. (2025). A study on topology optimization of landing gear parts. Celal Bayar University Journal of Science, 21(2), 35–46. https://doi.org/10.18466/cbayarfbe.1539030

Khot, M. B., Prekash, A., Gopalakrishna, R., Nanda, K., & Ghosh, H. (2025). Modelling and optimisation of structural parameters of main landing gear during touchdown and taxing. International Journal of Engineering Systems Modelling and Simulation, 16(5), 294–301. https://doi.org/10.1504/IJESMS.2025.148256

Dagal, I., Mbasso, W. F., Ambe, H., Erol, B., & Jangir, P. (2025). Adaptive fuzzy logic control framework for aircraft landing gear automation: Optimized design, real-time response, and enhanced safety. International Journal of Aeronautical and Space Sciences, 1–29. https://doi.org/10.1007/s42405-025-00922-w

Wong, J., Ryan, L., & Kim, I. Y. (2018). Design optimization of aircraft landing gear assembly under dynamic loading. Structural and Multidisciplinary Optimization, 57(3), 1357–1375. https://doi.org/10.1007/s00158-017-1817-y

Wunderlich, T. F., & Dähne, S. (2025). Design and optimization of adaptive wings for highly efficient long-range aircraft. Journal of Aircraft, 1–17. https://doi.org/10.2514/1.C038307

Lin, Q., Yang, C., Bai, Y., & Qin, J. (2024). Structural strength analysis and optimization of commercial aircraft nose landing gear under towing taxi-out conditions using finite element simulation and modal testing. Aerospace, 11(5), 414. https://doi.org/10.3390/aerospace11050414

Zhou, H., Zhang, Y., Luo, L., Sun, J., & Ren, L. (2024). Research progress on aircraft landing gear dynamics modeling and simulation methods. In 2024 2nd Asian Aerospace and Astronautics Conference (AAAC) (pp. 244–249). IEEE. https://doi.org/10.1109/AAAC63570.2024.11027352

Gan, S., Fang, X., & Wei, X. (2021). Parametric analysis on landing gear strut friction of light aircraft for touchdown performance. Applied Sciences, 11(12), 5445. https://doi.org/10.3390/app11125445

Tumiati, S. (2018). A multidisciplinary framework for aircraft landing gear brake actuation design [Doctoral dissertation, Politecnico di Torino].

Akçay, Ö., & Ilkılıç, C. (2025). Light-weight design of aerospace components using genetic algorithm and dandelion optimization algorithm. International Journal of Aeronautical and Space Sciences, 26(5), 2898–2909. https://doi.org/10.1007/s42405-025-00900-2

Sun, Y. P., Feng, H., Zheng, B., Wen, J. R., Chao, A. F., & Fei, C. W. (2025). Multi-agent reinforcement symbolic regression for the fatigue life prediction of aircraft landing gear. Aerospace, 12(8), 718. https://doi.org/10.3390/aerospace12080718

Ma, Y., Du, Y., Wang, Y., Zhang, K., & Han, Z. (2025). Aerostructural comparative study of composite strut- and truss-braced wing configurations. Journal of Aircraft, 1–11. https://doi.org/10.2514/1.C038551

Carvalho, J., Cavallaro, R., & Cini, A. (2025). Structural optimisation for mass estimation of large-aspect-ratio wings with distributed hybrid propulsion. Engineering Proceedings, 90(1), 85. https://doi.org/10.3390/engproc2025090085

İnce, Ö. S., Alpan, O., Şen, İ., & Girard, H. (2025). Optimized lattice structure design and analysis for aircraft brackets with an evaluation of additive manufacturing viability. In Advances in Aerospace Engineering (pp. 76–94). CRC Press. https://doi.org/10.1201/9781003370659-5

Ikpe, A. E., Owunna, I., & Paul, S. (2018). Finite element analysis of aircraft tire behaviour under overloaded aircraft landing phase. Aeronautics and Aerospace Open Access Journal, 2(1), 34–39. https://doi.org/10.15406/aaoaj.2018.02.00026

Xiao, X. Z., Zhao, Y. Y., Wu, H., & Zhu, G. S. (2025). Dynamic analysis of nose landing gear shimmy considering strut height and experiment on the test platform. Open Journal of Applied Sciences, 15, 919–937. https://doi.org/10.4236/ojapps.2025.154062

Ahmad, M. A., Ali Shah, S. I., Khan, S. A., Khan, H. A., & Shams, T. A. (2023). A novel framework for qualification of a composite-based main landing gear strut of a lightweight aircraft. Polymers, 15, 1402. https://doi.org/10.3390/polym15061402

Edem, I., Owunna, I., Ikpe, A. E., & Ikpe, E. E. (2016). The future of conventional aircraft ground propulsion systems in relation to fuel consumption and CO₂ emission. International Journal of Thermal & Environmental Engineering, 13(2), 91–100.

Modelling and Optimization of Strut Configurations in Aircraft Landing Gear Assembly for Effective In-Service Duty Cycle

Authors

DOI:

Keywords:

Abstract

Downloads

References

Downloads

Published

Issue

Section

License

How to Cite

Jouranl info

Information